Propagation guide

How to propagate Ruby Necklace (Othonna capensis) — step by step

Also called Ruby Necklace, String of Rubies, Little Pickles, Trailing Othonna, Cape Aster.

The best way to propagate ruby necklace

The reliable, beginner-friendly way to propagate ruby necklace is nodal stem cuttings in water or soil. It suits this species because of how it grows: fast-growing, low and creeping trailing succulent. slender purple stems carry small, elongated bean- or pickle-shaped blue-green leaves that turn ruby-red to magenta under sun, drought or cool stress. in its growing season it pushes out small, bright-yellow daisy-like flowers on thin stalks, which often open in sun and close in the evening.. Very easy from stem cuttings. Snip a healthy length of stem, let the cut end callus for a day or two, then lay it on or shallowly insert it into gritty succulent mix. Keep barely moist and roots typically form within a couple of weeks. It also propagates from individual leaves and by simply pinning trailing stems onto soil, where they root at the nodes.

For the wider picture of which technique suits which plant, our guide to plant propagation methods compares water, soil, leaf, division and offset propagation side by side.

Step-by-step: propagating ruby necklace

Find a node. Locate a node on a healthy ruby necklace vine — the small bump where a leaf or aerial root meets the stem. New roots only emerge from nodes, so every cutting must contain one.
Take the cutting. With clean, sharp scissors cut about 1 cm below the node at a slight angle. Aim for a 10–15 cm cutting with 2–3 nodes and one or two leaves at the top.
Strip lower leaves. Remove leaves from the bottom node(s) so the bare nodes can sit in water or soil. A submerged leaf rots and fouls the water.
Root it. Stand the cutting in a glass of room-temperature water with the node(s) covered, or push it into moist potting mix. Place in bright indirect light. Change the water every 4–5 days.
Pot up. When the new roots are 3–5 cm long (usually 2–4 weeks), pot the cutting into a small container of free-draining cactus and succulent mix with heavy mineral grit and keep it slightly moister than normal for the first fortnight.

The alternative method

If the main route does not suit your plant or setup, soil propagation (skip the water glass) is the next best option for ruby necklace. Push the nodal cutting straight into moist potting mix instead of water — the roots that form are soil-adapted from day one, so there is no transition shock, though you cannot watch progress through the glass.

Timeline to roots

Realistically: roots in 2–4 weeks; pot up at 4–6 weeks. These numbers assume spring or summer warmth and bright indirect light. In a cold, dark room — or in winter dormancy — the same ruby necklace propagation can take twice as long or stall completely, so do not panic if progress looks slow out of season. Patience beats poking: disturbing a forming root system to “check” on it is a common way to set it back.

Common failure points

Taking a cutting with no node — leaves alone never root, no matter how long they sit in water.
Letting the water go stagnant; refresh it every 4–5 days or the cut end slimes and rots.
Potting up water-rooted cuttings too late — long, brittle water roots struggle to adapt to soil. Move them at 3–5 cm.
Propagating off a stressed, pest-ridden or recently-repotted ruby necklace — always take material from a healthy, established parent.

When to do it

The best window is spring and summer (active growth). Propagation is energetically expensive for a plant, and it only has the spare resources to build new roots when it is already growing actively, warm and well-lit. Out-of-season attempts are not pointless, but expect lower success and a longer wait.

Aftercare

For the first two to three weeks after potting, keep the new ruby necklace slightly moister than you would a mature plant and out of direct sun while the young roots adapt from water (or cutting medium) to soil. Hold off all fertiliser until you see a flush of new top growth — feeding a rootless cutting only burns it. Match the parent's needs as the new ruby necklace settles: Wants the brightest spot you can give it: a south- or west-facing window, ideally with a few hours of gentle direct sun. The more light it gets, the deeper the stems and bean-like leaves flush ruby-purple; in low light they stay green and the trailing stems stretch and grow leggy. Outdoors it takes full sun once acclimatised.

Ruby Necklace propagation — frequently asked questions

What is the best way to propagate ruby necklace?

Nodal stem cuttings in water or soil is the most reliable method for ruby necklace. The best way to propagate ruby necklace is a stem cutting taken just below a node. A cutting must include at least one node — the leaves alone will not root. Place the node in water or moist soil in bright indirect light. Roots appear in 2–4 weeks; pot up at 4–6 weeks.

Do you need a node to propagate ruby necklace?

Yes — absolutely. Roots only emerge from a node, so every ruby necklace cutting must include at least one. A length of stem or a leaf with no node will sit in water indefinitely and never root.

How long does it take ruby necklace to root?

Roots in 2–4 weeks; pot up at 4–6 weeks. Timing varies with warmth and light — propagations move fastest in spring and summer when the plant is in active growth, and can stall almost completely in a cold, dark winter.

What is the best time of year to propagate ruby necklace?

Spring and summer (active growth). Root and shoot development is metabolically demanding, so propagating during the active growing season gives noticeably higher success rates and faster results than attempting it in dormancy.

Can you propagate ruby necklace in water?

Yes — ruby necklace roots readily in a glass of water as long as a node is submerged. Water propagation is the most beginner-friendly route; just move the cutting to soil before the water roots get long and brittle (around 3–5 cm).