Propagation guide

How to propagate Prince of Wales Juniper (Juniperus horizontalis 'Prince of Wales') — step by step

Also called Prince of Wales Juniper, Creeping Juniper.

The best way to propagate prince of wales juniper

The reliable, beginner-friendly way to propagate prince of wales juniper is division of the crown / rhizome. It suits this species because of how it grows: prostrate, slow-to-moderate spreading mat; flat, dense ground cover with fine foliage that takes on purplish winter colour.. Take semi-hardwood cuttings in late summer to autumn, using rooting hormone in a free-draining medium; trailing stems also self-layer. As a named cultivar it must be propagated vegetatively, not from seed, to stay true.

For the wider picture of which technique suits which plant, our guide to plant propagation methods compares water, soil, leaf, division and offset propagation side by side.

Step-by-step: propagating prince of wales juniper

Water and unpot. Water prince of wales juniper the day before, then slide the whole plant out and gently shake or wash soil off the root mass.
Find natural splits. Look for separate crowns or fans of growth. Tease them apart by hand where you can; use a clean knife only where roots are matted.
Cut into divisions. Make divisions that each keep several healthy growing points and a strong share of roots — bigger divisions recover faster.
Trim and repot. Trim any rotten roots, then pot each division at its original depth in well-drained sandy or gravelly soil.
Aftercare. Water in, keep out of harsh sun and slightly humid for 3–6 weeks while roots re-establish. Hold off feeding until new growth appears.

The alternative method

If the main route does not suit your plant or setup, potting up naturally offsetting side crowns is the next best option for prince of wales juniper. Many of these plants also throw side crowns or offsets you can pot up individually without lifting the whole plant, which is gentler if the parent is large or established.

Timeline to roots

Realistically: full plants from day one; settles in 3–6 weeks. These numbers assume spring or summer warmth and bright indirect light. In a cold, dark room — or in winter dormancy — the same prince of wales juniper propagation can take twice as long or stall completely, so do not panic if progress looks slow out of season. Patience beats poking: disturbing a forming root system to “check” on it is a common way to set it back.

Common failure points

Making divisions too small, with too few roots or growing points to recover.
Dividing in the heat of summer instead of spring or at repotting, adding avoidable stress.
Planting divisions too deep or too shallow relative to their original soil line.
Propagating off a stressed, pest-ridden or recently-repotted prince of wales juniper — always take material from a healthy, established parent.

When to do it

The best window is spring, or at repotting time. Propagation is energetically expensive for a plant, and it only has the spare resources to build new roots when it is already growing actively, warm and well-lit. Out-of-season attempts are not pointless, but expect lower success and a longer wait.

Aftercare

Water divisions in well, keep them out of harsh sun and slightly humid for three to six weeks, and delay feeding until new prince of wales juniper growth appears. Bigger divisions bounce back fastest. Match the parent's needs as the new prince of wales juniper settles: Full sun, 6 or more hours daily, keeps the carpet dense and colourful. In shade it grows sparse, loses its winter purple tones and is more disease-prone.

Prince of Wales Juniper propagation — frequently asked questions

What is the best way to propagate prince of wales juniper?

Division of the crown / rhizome is the most reliable method for prince of wales juniper. Propagate prince of wales juniper by division. Lift the plant, tease or cut the crown into clumps that each keep healthy roots and several growing points, then repot. You get full-sized plants from day one; they settle in 3–6 weeks. Spring or repotting time is ideal.

Do you need a node to propagate prince of wales juniper?

For prince of wales juniper the rooting structure is division of the crown / rhizome, so a classic "node" matters less than starting with the right plant material — Lift the plant, tease or cut the crown into clumps that each keep healthy roots and several growing points, then repot.

How long does it take prince of wales juniper to root?

Full plants from day one; settles in 3–6 weeks. Timing varies with warmth and light — propagations move fastest in spring and summer when the plant is in active growth, and can stall almost completely in a cold, dark winter.

What is the best time of year to propagate prince of wales juniper?

Spring, or at repotting time. Root and shoot development is metabolically demanding, so propagating during the active growing season gives noticeably higher success rates and faster results than attempting it in dormancy.

Can you propagate prince of wales juniper in water?

Not really — prince of wales juniper is divided into rooted clumps and potted straight into mix. Water propagation does not apply to division; each piece already has its own roots.