Propagation guide

How to propagate Welwitsch's Anchomanes (Anchomanes welwitschii) — step by step

Also called Welwitsch's Anchomanes, African Anchomanes.

The best way to propagate welwitsch's anchomanes

The reliable, beginner-friendly way to propagate welwitsch's anchomanes is nodal stem cuttings in water or soil. It suits this species because of how it grows: tuberous geophytic aroid; produces a single large compound leaf annually, dying back to tuber in dry season. Propagate by division of tuber offsets when repotting in spring just before growth resumes. Each section must have at least one visible growth bud. Allow cut surfaces to callous for 24 hours before planting in fresh compost. Seed propagation is possible but very slow.

For the wider picture of which technique suits which plant, our guide to plant propagation methods compares water, soil, leaf, division and offset propagation side by side.

Step-by-step: propagating welwitsch's anchomanes

Find a node. Locate a node on a healthy welwitsch's anchomanes vine — the small bump where a leaf or aerial root meets the stem. New roots only emerge from nodes, so every cutting must contain one.
Take the cutting. With clean, sharp scissors cut about 1 cm below the node at a slight angle. Aim for a 10–15 cm cutting with 2–3 nodes and one or two leaves at the top.
Strip lower leaves. Remove leaves from the bottom node(s) so the bare nodes can sit in water or soil. A submerged leaf rots and fouls the water.
Root it. Stand the cutting in a glass of room-temperature water with the node(s) covered, or push it into moist potting mix. Place in bright indirect light. Change the water every 4–5 days.
Pot up. When the new roots are 3–5 cm long (usually 2–4 weeks), pot the cutting into a small container of rich, loose, free-draining tropical loam and keep it slightly moister than normal for the first fortnight.

The alternative method

If the main route does not suit your plant or setup, soil propagation (skip the water glass) is the next best option for welwitsch's anchomanes. Push the nodal cutting straight into moist potting mix instead of water — the roots that form are soil-adapted from day one, so there is no transition shock, though you cannot watch progress through the glass.

Timeline to roots

Realistically: roots in 2–4 weeks; pot up at 4–6 weeks. These numbers assume spring or summer warmth and bright indirect light. In a cold, dark room — or in winter dormancy — the same welwitsch's anchomanes propagation can take twice as long or stall completely, so do not panic if progress looks slow out of season. Patience beats poking: disturbing a forming root system to “check” on it is a common way to set it back.

Common failure points

Taking a cutting with no node — leaves alone never root, no matter how long they sit in water.
Letting the water go stagnant; refresh it every 4–5 days or the cut end slimes and rots.
Potting up water-rooted cuttings too late — long, brittle water roots struggle to adapt to soil. Move them at 3–5 cm.
Propagating off a stressed, pest-ridden or recently-repotted welwitsch's anchomanes — always take material from a healthy, established parent.

When to do it

The best window is spring and summer (active growth). Propagation is energetically expensive for a plant, and it only has the spare resources to build new roots when it is already growing actively, warm and well-lit. Out-of-season attempts are not pointless, but expect lower success and a longer wait.

Aftercare

For the first two to three weeks after potting, keep the new welwitsch's anchomanes slightly moister than you would a mature plant and out of direct sun while the young roots adapt from water (or cutting medium) to soil. Hold off all fertiliser until you see a flush of new top growth — feeding a rootless cutting only burns it. Match the parent's needs as the new welwitsch's anchomanes settles: In its native African forest understorey, it receives bright to moderate indirect light filtered through a canopy. Indoors, place in a bright room away from direct sun. Too little light results in weak, etiolated growth; direct sun scorches the foliage.

Welwitsch's Anchomanes propagation — frequently asked questions

What is the best way to propagate welwitsch's anchomanes?

Nodal stem cuttings in water or soil is the most reliable method for welwitsch's anchomanes. The best way to propagate welwitsch's anchomanes is a stem cutting taken just below a node. A cutting must include at least one node — the leaves alone will not root. Place the node in water or moist soil in bright indirect light. Roots appear in 2–4 weeks; pot up at 4–6 weeks.

Do you need a node to propagate welwitsch's anchomanes?

Yes — absolutely. Roots only emerge from a node, so every welwitsch's anchomanes cutting must include at least one. A length of stem or a leaf with no node will sit in water indefinitely and never root.

How long does it take welwitsch's anchomanes to root?

Roots in 2–4 weeks; pot up at 4–6 weeks. Timing varies with warmth and light — propagations move fastest in spring and summer when the plant is in active growth, and can stall almost completely in a cold, dark winter.

What is the best time of year to propagate welwitsch's anchomanes?

Spring and summer (active growth). Root and shoot development is metabolically demanding, so propagating during the active growing season gives noticeably higher success rates and faster results than attempting it in dormancy.

Can you propagate welwitsch's anchomanes in water?

Yes — welwitsch's anchomanes roots readily in a glass of water as long as a node is submerged. Water propagation is the most beginner-friendly route; just move the cutting to soil before the water roots get long and brittle (around 3–5 cm).