Propagation guide

How to propagate Sticky Jerusalem Sage (Phlomis viscosa) — step by step

Also called Sticky Jerusalem sage, Viscous phlomis.

The best way to propagate sticky jerusalem sage

The reliable, beginner-friendly way to propagate sticky jerusalem sage is division of the crown / rhizome. It suits this species because of how it grows: upright, bushy sub-shrub or perennial with stiff, sticky branching stems and tiered flower whorls.. Semi-ripe cuttings 8–10 cm long taken in late summer root well in a gritty, free-draining compost; seed sown in spring germinates reliably at 18–20°C and plants may flower in their first year.

For the wider picture of which technique suits which plant, our guide to plant propagation methods compares water, soil, leaf, division and offset propagation side by side.

Step-by-step: propagating sticky jerusalem sage

Water and unpot. Water sticky jerusalem sage the day before, then slide the whole plant out and gently shake or wash soil off the root mass.
Find natural splits. Look for separate crowns or fans of growth. Tease them apart by hand where you can; use a clean knife only where roots are matted.
Cut into divisions. Make divisions that each keep several healthy growing points and a strong share of roots — bigger divisions recover faster.
Trim and repot. Trim any rotten roots, then pot each division at its original depth in free-draining, poor to moderately fertile, alkaline or neutral.
Aftercare. Water in, keep out of harsh sun and slightly humid for 3–6 weeks while roots re-establish. Hold off feeding until new growth appears.

The alternative method

If the main route does not suit your plant or setup, potting up naturally offsetting side crowns is the next best option for sticky jerusalem sage. Many of these plants also throw side crowns or offsets you can pot up individually without lifting the whole plant, which is gentler if the parent is large or established.

Timeline to roots

Realistically: full plants from day one; settles in 3–6 weeks. These numbers assume spring or summer warmth and bright indirect light. In a cold, dark room — or in winter dormancy — the same sticky jerusalem sage propagation can take twice as long or stall completely, so do not panic if progress looks slow out of season. Patience beats poking: disturbing a forming root system to “check” on it is a common way to set it back.

Common failure points

Making divisions too small, with too few roots or growing points to recover.
Dividing in the heat of summer instead of spring or at repotting, adding avoidable stress.
Planting divisions too deep or too shallow relative to their original soil line.
Propagating off a stressed, pest-ridden or recently-repotted sticky jerusalem sage — always take material from a healthy, established parent.

When to do it

The best window is spring, or at repotting time. Propagation is energetically expensive for a plant, and it only has the spare resources to build new roots when it is already growing actively, warm and well-lit. Out-of-season attempts are not pointless, but expect lower success and a longer wait.

Aftercare

Water divisions in well, keep them out of harsh sun and slightly humid for three to six weeks, and delay feeding until new sticky jerusalem sage growth appears. Bigger divisions bounce back fastest. Match the parent's needs as the new sticky jerusalem sage settles: Full sun is essential; even partial afternoon shade noticeably reduces flower output and makes the plant straggly in cooler climates.

Sticky Jerusalem Sage propagation — frequently asked questions

What is the best way to propagate sticky jerusalem sage?

Division of the crown / rhizome is the most reliable method for sticky jerusalem sage. Propagate sticky jerusalem sage by division. Lift the plant, tease or cut the crown into clumps that each keep healthy roots and several growing points, then repot. You get full-sized plants from day one; they settle in 3–6 weeks. Spring or repotting time is ideal.

Do you need a node to propagate sticky jerusalem sage?

For sticky jerusalem sage the rooting structure is division of the crown / rhizome, so a classic "node" matters less than starting with the right plant material — Lift the plant, tease or cut the crown into clumps that each keep healthy roots and several growing points, then repot.

How long does it take sticky jerusalem sage to root?

Full plants from day one; settles in 3–6 weeks. Timing varies with warmth and light — propagations move fastest in spring and summer when the plant is in active growth, and can stall almost completely in a cold, dark winter.

What is the best time of year to propagate sticky jerusalem sage?

Spring, or at repotting time. Root and shoot development is metabolically demanding, so propagating during the active growing season gives noticeably higher success rates and faster results than attempting it in dormancy.

Can you propagate sticky jerusalem sage in water?

Not really — sticky jerusalem sage is divided into rooted clumps and potted straight into mix. Water propagation does not apply to division; each piece already has its own roots.