Propagation guide

How to propagate Ficus Abidjan (burgundy rubber plant) (Ficus elastica 'Abidjan') — step by step

Also called burgundy rubber plant, burgundy rubber tree, black prince rubber plant, Abidjan rubber plant, rubber fig 'Abidjan'.

The best way to propagate ficus abidjan (burgundy rubber plant)

The reliable, beginner-friendly way to propagate ficus abidjan (burgundy rubber plant) is nodal stem cuttings in water or soil. It suits this species because of how it grows: upright single-trunk or branched evergreen tree with large, thick, oval leaves; new growth emerges red before maturing to glossy near-black burgundy with red mid-veins.. Propagate from stem or tip cuttings with one or two leaves, or by air-layering thicker stems (more reliable for mature plants). Let the cut surface air-dry so the milky sap seals over before rooting in water or moist mix; roots typically form in 4-6 weeks. Wear gloves, as the latex irritates skin.

For the wider picture of which technique suits which plant, our guide to plant propagation methods compares water, soil, leaf, division and offset propagation side by side.

Step-by-step: propagating ficus abidjan (burgundy rubber plant)

Find a node. Locate a node on a healthy ficus abidjan (burgundy rubber plant) vine — the small bump where a leaf or aerial root meets the stem. New roots only emerge from nodes, so every cutting must contain one.
Take the cutting. With clean, sharp scissors cut about 1 cm below the node at a slight angle. Aim for a 10–15 cm cutting with 2–3 nodes and one or two leaves at the top.
Strip lower leaves. Remove leaves from the bottom node(s) so the bare nodes can sit in water or soil. A submerged leaf rots and fouls the water.
Root it. Stand the cutting in a glass of room-temperature water with the node(s) covered, or push it into moist potting mix. Place in bright indirect light. Change the water every 4–5 days.
Pot up. When the new roots are 3–5 cm long (usually 2–4 weeks), pot the cutting into a small container of free-draining, soil-based houseplant mix and keep it slightly moister than normal for the first fortnight.

The alternative method

If the main route does not suit your plant or setup, soil propagation (skip the water glass) is the next best option for ficus abidjan (burgundy rubber plant). Push the nodal cutting straight into moist potting mix instead of water — the roots that form are soil-adapted from day one, so there is no transition shock, though you cannot watch progress through the glass.

Timeline to roots

Realistically: roots in 2–4 weeks; pot up at 4–6 weeks. These numbers assume spring or summer warmth and bright indirect light. In a cold, dark room — or in winter dormancy — the same ficus abidjan (burgundy rubber plant) propagation can take twice as long or stall completely, so do not panic if progress looks slow out of season. Patience beats poking: disturbing a forming root system to “check” on it is a common way to set it back.

Common failure points

Taking a cutting with no node — leaves alone never root, no matter how long they sit in water.
Letting the water go stagnant; refresh it every 4–5 days or the cut end slimes and rots.
Potting up water-rooted cuttings too late — long, brittle water roots struggle to adapt to soil. Move them at 3–5 cm.
Propagating off a stressed, pest-ridden or recently-repotted ficus abidjan (burgundy rubber plant) — always take material from a healthy, established parent.

When to do it

The best window is spring and summer (active growth). Propagation is energetically expensive for a plant, and it only has the spare resources to build new roots when it is already growing actively, warm and well-lit. Out-of-season attempts are not pointless, but expect lower success and a longer wait.

Aftercare

For the first two to three weeks after potting, keep the new ficus abidjan (burgundy rubber plant) slightly moister than you would a mature plant and out of direct sun while the young roots adapt from water (or cutting medium) to soil. Hold off all fertiliser until you see a flush of new top growth — feeding a rootless cutting only burns it. Match the parent's needs as the new ficus abidjan (burgundy rubber plant) settles: Bright indirect light keeps the burgundy colour rich and the leaves well-spaced. It tolerates moderate light, but in low light the new foliage emerges greener and loses its dark tone, and growth gets leggy. Avoid direct midday sun, which scorches the leaves.

Ficus Abidjan (burgundy rubber plant) propagation — frequently asked questions

What is the best way to propagate ficus abidjan (burgundy rubber plant)?

Nodal stem cuttings in water or soil is the most reliable method for ficus abidjan (burgundy rubber plant). The best way to propagate ficus abidjan (burgundy rubber plant) is a stem cutting taken just below a node. A cutting must include at least one node — the leaves alone will not root. Place the node in water or moist soil in bright indirect light. Roots appear in 2–4 weeks; pot up at 4–6 weeks.

Do you need a node to propagate ficus abidjan (burgundy rubber plant)?

Yes — absolutely. Roots only emerge from a node, so every ficus abidjan (burgundy rubber plant) cutting must include at least one. A length of stem or a leaf with no node will sit in water indefinitely and never root.

How long does it take ficus abidjan (burgundy rubber plant) to root?

Roots in 2–4 weeks; pot up at 4–6 weeks. Timing varies with warmth and light — propagations move fastest in spring and summer when the plant is in active growth, and can stall almost completely in a cold, dark winter.

What is the best time of year to propagate ficus abidjan (burgundy rubber plant)?

Spring and summer (active growth). Root and shoot development is metabolically demanding, so propagating during the active growing season gives noticeably higher success rates and faster results than attempting it in dormancy.

Can you propagate ficus abidjan (burgundy rubber plant) in water?

Yes — ficus abidjan (burgundy rubber plant) roots readily in a glass of water as long as a node is submerged. Water propagation is the most beginner-friendly route; just move the cutting to soil before the water roots get long and brittle (around 3–5 cm).