Propagation guide

How to propagate String of Tears (Curio herreanus) — step by step

Also called String of tears, String of beads, String of watermelons, String of raindrops, Gooseberry plant.

The best way to propagate string of tears

The reliable, beginner-friendly way to propagate string of tears is nodal stem cuttings in water or soil. It suits this species because of how it grows: fast-growing, trailing and ground-creeping evergreen succulent with slender stems lined by plump, oval to tear-shaped beads, often marked with translucent leaf "windows" and faint purple stripes. looks best spilling from a hanging pot or a high shelf.. Very easy from stem cuttings. Snip a healthy strand a few centimetres long, let the cut end callus for a day or two, then lay it on or shallowly press it into gritty succulent mix and keep barely moist until roots form. Pieces also root readily where beads touch the soil, so you can pin a strand down on the surface to multiply the plant.

For the wider picture of which technique suits which plant, our guide to plant propagation methods compares water, soil, leaf, division and offset propagation side by side.

Step-by-step: propagating string of tears

Find a node. Locate a node on a healthy string of tears vine — the small bump where a leaf or aerial root meets the stem. New roots only emerge from nodes, so every cutting must contain one.
Take the cutting. With clean, sharp scissors cut about 1 cm below the node at a slight angle. Aim for a 10–15 cm cutting with 2–3 nodes and one or two leaves at the top.
Strip lower leaves. Remove leaves from the bottom node(s) so the bare nodes can sit in water or soil. A submerged leaf rots and fouls the water.
Root it. Stand the cutting in a glass of room-temperature water with the node(s) covered, or push it into moist potting mix. Place in bright indirect light. Change the water every 4–5 days.
Pot up. When the new roots are 3–5 cm long (usually 2–4 weeks), pot the cutting into a small container of free-draining cactus and succulent mix amended with plenty of mineral grit. and keep it slightly moister than normal for the first fortnight.

The alternative method

If the main route does not suit your plant or setup, soil propagation (skip the water glass) is the next best option for string of tears. Push the nodal cutting straight into moist potting mix instead of water — the roots that form are soil-adapted from day one, so there is no transition shock, though you cannot watch progress through the glass.

Timeline to roots

Realistically: roots in 2–4 weeks; pot up at 4–6 weeks. These numbers assume spring or summer warmth and bright indirect light. In a cold, dark room — or in winter dormancy — the same string of tears propagation can take twice as long or stall completely, so do not panic if progress looks slow out of season. Patience beats poking: disturbing a forming root system to “check” on it is a common way to set it back.

Common failure points

Taking a cutting with no node — leaves alone never root, no matter how long they sit in water.
Letting the water go stagnant; refresh it every 4–5 days or the cut end slimes and rots.
Potting up water-rooted cuttings too late — long, brittle water roots struggle to adapt to soil. Move them at 3–5 cm.
Propagating off a stressed, pest-ridden or recently-repotted string of tears — always take material from a healthy, established parent.

When to do it

The best window is spring and summer (active growth). Propagation is energetically expensive for a plant, and it only has the spare resources to build new roots when it is already growing actively, warm and well-lit. Out-of-season attempts are not pointless, but expect lower success and a longer wait.

Aftercare

For the first two to three weeks after potting, keep the new string of tears slightly moister than you would a mature plant and out of direct sun while the young roots adapt from water (or cutting medium) to soil. Hold off all fertiliser until you see a flush of new top growth — feeding a rootless cutting only burns it. Match the parent's needs as the new string of tears settles: Wants several hours of bright, filtered light daily, ideally near an east or shaded south/west window. Direct midday summer sun can scorch the beads, while too little light causes leggy, sparse strands and fades the attractive purple tints. A few hours of gentle morning sun deepens leaf colour.

String of Tears propagation — frequently asked questions

What is the best way to propagate string of tears?

Nodal stem cuttings in water or soil is the most reliable method for string of tears. The best way to propagate string of tears is a stem cutting taken just below a node. A cutting must include at least one node — the leaves alone will not root. Place the node in water or moist soil in bright indirect light. Roots appear in 2–4 weeks; pot up at 4–6 weeks.

Do you need a node to propagate string of tears?

Yes — absolutely. Roots only emerge from a node, so every string of tears cutting must include at least one. A length of stem or a leaf with no node will sit in water indefinitely and never root.

How long does it take string of tears to root?

Roots in 2–4 weeks; pot up at 4–6 weeks. Timing varies with warmth and light — propagations move fastest in spring and summer when the plant is in active growth, and can stall almost completely in a cold, dark winter.

What is the best time of year to propagate string of tears?

Spring and summer (active growth). Root and shoot development is metabolically demanding, so propagating during the active growing season gives noticeably higher success rates and faster results than attempting it in dormancy.

Can you propagate string of tears in water?

Yes — string of tears roots readily in a glass of water as long as a node is submerged. Water propagation is the most beginner-friendly route; just move the cutting to soil before the water roots get long and brittle (around 3–5 cm).