Propagation guide

How to propagate Button fern (Pellaea rotundifolia) — step by step

Also called New Zealand button fern, tarawera.

The best way to propagate button fern

A quick warning first, because it is the single most common mistake: button fern cannot be propagated from a leaf or stem cutting. Button fern is a fern — it has no stem nodes, so a severed frond simply rots. The correct route is division of the rootball (or spore sowing for the patient), covered in full below.

For the wider picture of which technique suits which plant, our guide to plant propagation methods compares water, soil, leaf, division and offset propagation side by side.

Step-by-step: propagating button fern

Know what does NOT work. Button fern cannot be propagated from a leaf or frond cutting — there is no node to root. Division is the reliable method; spores are the advanced one.
Unpot a mature clump. Slide a well-established button fern out of its pot and shake or wash soil from the rootball so you can see the crowns.
Cut into sections. Using a clean serrated knife, slice the rootball into 2–4 sections, each keeping a generous fan of fronds and a solid share of roots.
Repot and recover. Pot each division in peat-free, moisture-retentive mix, water well, and keep humid and out of direct sun for 4–8 weeks while it re-establishes.
Spore route (optional). When the sori on the frond undersides turn brown, drop a frond in a paper bag, then sprinkle the released spores on sterile, moist mix under a clear lid. Expect a green film, then tiny ferns, over many months. Note: many cultivated ferns are sterile.

The alternative method

If the main route does not suit your plant or setup, spore propagation on sterile medium is the next best option for button fern. Spore sowing can yield large numbers of plants for nothing, but it is slow (many months), needs sterile conditions, and fails on the many sterile cultivars — division is the practical choice for almost everyone.

Timeline to roots

Realistically: division establishes in 4–8 weeks; spores take many months. These numbers assume spring or summer warmth and bright indirect light. In a cold, dark room — or in winter dormancy — the same button fern propagation can take twice as long or stall completely, so do not panic if progress looks slow out of season. Patience beats poking: disturbing a forming root system to “check” on it is a common way to set it back.

Common failure points

Trying to root a frond or "leaf cutting" — ferns simply do not work this way.
Dividing into tiny pieces with too few roots; bigger divisions survive, fragments sulk and die.
Letting divisions dry out or sit in harsh sun while they re-establish.
Expecting spores to work on a sterile cultivar (many ornamental ferns set no viable spores).

When to do it

The best window is spring (division); when sori ripen (spores). Propagation is energetically expensive for a plant, and it only has the spare resources to build new roots when it is already growing actively, warm and well-lit. Out-of-season attempts are not pointless, but expect lower success and a longer wait.

Aftercare

Fern divisions resent disturbance — keep the new button fern humid (a covered tray or a pebble tray helps), out of direct sun and evenly moist for four to eight weeks while it re-roots. Spore-grown ferns stay under cover until the little plants are big enough to prick out. Match the parent's needs as the new button fern settles: Medium to bright indirect light; avoid direct sun.

Button fern propagation — frequently asked questions

What is the best way to propagate button fern?

Division of the rootball (or spore sowing for the patient) is the most reliable method for button fern. Propagate button fern by division, not cuttings — ferns do not root from leaf or stem pieces. Unpot a mature clump, slice the rootball into sections each with fronds and roots, and repot. For a challenge, sow the dust-fine spores on sterile medium; it takes many months.

Can you propagate button fern from a leaf or frond cutting?

No. Button fern is a fern (or fern-ally) and has no stem nodes, so a cut frond placed in water or soil will simply rot — it cannot produce roots or a new plant. Division of an established rootball is the dependable method; spores are the slow, advanced alternative, and many cultivated ferns are sterile so even that may not work.

How long does it take button fern to root?

Division establishes in 4–8 weeks; spores take many months. Timing varies with warmth and light — propagations move fastest in spring and summer when the plant is in active growth, and can stall almost completely in a cold, dark winter.

What is the best time of year to propagate button fern?

Spring (division); when sori ripen (spores). Root and shoot development is metabolically demanding, so propagating during the active growing season gives noticeably higher success rates and faster results than attempting it in dormancy.

Can you propagate button fern in water?

No. There is no button fern cutting that roots in water — ferns are propagated by division or spores, not by water-rooting plant pieces.