Propagation guide

How to propagate Burro's tail (Sedum morganianum) — step by step

Also called donkey tail, horse tail, lamb tail.

The best way to propagate burro's tail

The reliable, beginner-friendly way to propagate burro's tail is trailing strand cuttings laid on the soil surface. It suits this species because of how it grows: trailing succulent. Dropped leaves root in dry succulent mix within 2-3 weeks; cuttings the same.

For the wider picture of which technique suits which plant, our guide to plant propagation methods compares water, soil, leaf, division and offset propagation side by side.

Step-by-step: propagating burro's tail

Cut a healthy strand. Snip a 10–20 cm length of healthy burro's tail just below a node. Several strands in one pot give a full plant fastest.
Strip the rooting section. Pull the beads/leaves off the lowest few centimetres so bare nodes will contact the soil.
Lay it on the soil. Coil the strand across barely-moist succulent mix so as many nodes as possible touch the surface. Pin it down with bent wire or a hairpin.
Keep nodes in contact. Mist lightly to settle it. Roots grow from every node touching soil within 2–4 weeks, and the strand pulls itself in.
Water-route option. One strand can also be hung with its lower nodes in a little water, then potted once roots reach 2–3 cm.

The alternative method

If the main route does not suit your plant or setup, water propagation of a single strand is the next best option for burro's tail. Suspend a single long strand with just its lower nodes touching a little water; pot it once the roots reach 2–3 cm. Soil-laying is still the higher-success route.

Timeline to roots

Realistically: roots from the nodes in 2–4 weeks. These numbers assume spring or summer warmth and bright indirect light. In a cold, dark room — or in winter dormancy — the same burro's tail propagation can take twice as long or stall completely, so do not panic if progress looks slow out of season. Patience beats poking: disturbing a forming root system to “check” on it is a common way to set it back.

Common failure points

Not letting the cut/leaf callus before it touches soil or water — the number-one cause of rot.
Over-watering propagations: mist or barely moisten, never soak, until real roots form.
Pulling a leaf that tears rather than detaching cleanly at the base — a torn leaf will not produce a baby.
Propagating off a stressed, pest-ridden or recently-repotted burro's tail — always take material from a healthy, established parent.

When to do it

The best window is spring and summer. Propagation is energetically expensive for a plant, and it only has the spare resources to build new roots when it is already growing actively, warm and well-lit. Out-of-season attempts are not pointless, but expect lower success and a longer wait.

Aftercare

Keep new burro's tail propagations bright but out of fierce direct sun, and water only lightly until a real root system has formed — overwatering now is fatal. Once established, switch to the parent's normal lean, dry rhythm. Match the parent's needs as the new burro's tail settles: Bright indirect light with hours of direct morning sun; pale washed-out look in low light.

Burro's tail propagation — frequently asked questions

What is the best way to propagate burro's tail?

Trailing strand cuttings laid on the soil surface is the most reliable method for burro's tail. Propagate burro's tail by laying trailing strands on the soil surface. Cut a healthy strand, lay it across moist succulent mix so the nodes touch the soil, and pin it down. Roots form from every buried node within 2–4 weeks. No glass of water needed.

Do you need a node to propagate burro's tail?

For burro's tail the rooting structure is trailing strand cuttings laid on the soil surface, so a classic "node" matters less than starting with the right plant material — Cut a healthy strand, lay it across moist succulent mix so the nodes touch the soil, and pin it down.

How long does it take burro's tail to root?

Roots from the nodes in 2–4 weeks. Timing varies with warmth and light — propagations move fastest in spring and summer when the plant is in active growth, and can stall almost completely in a cold, dark winter.

What is the best time of year to propagate burro's tail?

Spring and summer. Root and shoot development is metabolically demanding, so propagating during the active growing season gives noticeably higher success rates and faster results than attempting it in dormancy.

Can you propagate burro's tail in water?

Water propagation is not the ideal route for burro's tail. Succulent leaves and strands rot easily if they sit wet — callus the cut, then root on barely-moist gritty mix instead. A single strand can be suspended with only its nodes touching water if you prefer.